Owner's Setup Guide
GaugeX™ Lock Miter Router Bit

Setup Guide: Perfect Lock Miter Joints

Set up your bit once, the right way, and every corner comes out tight, flush and strong. This guide takes you from an unopened box to a perfect test joint in seven steps.

  • 20–30 min first setup
  • Under 1 min with a setup block
  • For 1-1/2″, 2″ and 2-3/4″ bits
A lock miter joint: part A cut flat and part B cut on edge lock into a 45° corner

Thank you for choosing GaugeX™. A lock miter looks tricky, but it comes down to two settings and two cuts. Keep this guide open at the router table for your first setup.

The whole method at a glance

One bit, one height, one fence setting. The two cuts mirror each other and lock into a self-aligning 45° corner.

HeightThe centre of the bit profile lines up with the centre of the board.
FenceThe bit sticks out from the fence by exactly one board thickness.
Part ALies flat on the table, inside face down.
Part BStands on edge, inside face against the fence.
00

Before you start

Get the right tools and perfectly prepared stock. Most setup problems start here.

What you need

  • Router table with a flat top and a fence square to the table. A tall fence (about 6″ / 150 mm) is best for the on-edge cut.
  • Router with a 1/2″ collet and variable speed. Use 2 hp or more for the 2-3/4″ bit.
  • Two featherboards (down and toward the fence) and a push block.
  • Marking gauge or combination square, pencil, calipers if you have them.

Prepare your stock

  • All parts must be flat, straight and exactly the same thickness. Any difference shows up as a step at the corner.
  • Check plywood with calipers, since sheets often vary.
  • Prepare 1–2 ft (30–60 cm) of extra stock for test cuts, double that the first time.
  • Mark every part A or B and mark the inside faces.
01

Choose the bit and speed

Match the bit to your stock thickness and slow the router down for larger bits.

GaugeX lock miter bits in three sizes
Three sizes, all with a 1/2″ shank. The max board thickness is the key spec.
BitMax boardTypical stockMax speed
1-1/2″
38.1 mm
11/16″ (17 mm)1/2″–5/8″ plywood, MDF, drawer sidesabout 18,000 RPM
2″
50.8 mm
7/8″ (22 mm)3/4″ boards and plywood16,000–18,000 RPM
2-3/4″
70 mm
1-3/16″ (30 mm)1″ hardwood, thick posts, furniture10,000–12,000 RPM

Rough cut or burning? Change the feed rate first. Raise the speed only a little, and never above the limit for that size.

02

Set the bit height

Centre the bit profile on the thickness of your board.

Bit height: centre of the profile lines up with the centre of the board
The middle of the stepped section lines up with the centreline of the board.
  1. Unplug the router. Insert the shank fully, back it out about 1/16″ (1–2 mm) and tighten the collet.
  2. Mark the centre of your stock. Scribe the edge with a marking gauge from both faces. Where the lines meet is the exact centre.
  3. Find the centre of the profile: halfway between where the stepped section starts and ends.
  4. Raise or lower the bit until the two centres line up. Get it close by eye; test cuts fine-tune it.

✓ Check: held against the bit, the board's centreline sits in the middle of the stepped profile.

03

Set the fence

The bit should stick out from the fence by exactly one board thickness.

Bridge method for setting the fence
The bridge method: two scraps on edge and a straightedge across them.
  1. Stand a scrap of your stock on edge against the fence on each side of the bit.
  2. Lay a straight board across their outer faces, bridging over the bit.
  3. Move the fence until the outermost cutter tip just touches the bridge, then lock the fence.
  4. Close the fence opening around the bit as far as possible and set your featherboards.

✓ Check: after a cut, the mitred edge comes to a crisp, knife-like point and the board is no narrower than before.

04

Cut part A, flat

The first half of the joint is cut with the board lying flat on the table.

Part A lies flat, inside face down
Part A: flat on the table, inside face down, edge against the fence.
  1. Lay the board flat, inside face down: the face that will be inside the box or cabinet.
  2. Keep the edge tight against the fence and feed right to left, against the bit's rotation, at a steady pace.
  3. Hold it down with a featherboard and finish the cut with a push block.

Cutting end grain? Back the cut with a square scrap of the same thickness to prevent tear-out.

05

Cut part B, on edge

The mating part is cut standing up, with the same bit height and fence.

Part B stands on edge, inside face against the fence
Part B: on edge, inside face against the fence, perfectly vertical.

Do not touch the bit height or the fence. Both parts must be cut with exactly the same settings.

  1. Stand the board on edge, inside face against the fence, and keep it perfectly vertical.
  2. Use a tall fence and a featherboard pressing the board toward the fence. A tall push block or simple sled makes this pass safer.
  3. Never cut narrow parts on edge. Rout wide boards first, then rip them to final width.
06

Test-fit and fine-tune

Cut one A and one B from scrap, push the corner together and read the result.

Test-fit results and how to correct them
Faces flush and a sharp corner mean you are ready to cut project parts.
  • Faces flush, corner sharp: you're done. Cut your project parts.
  • One face sticks out: adjust the bit height by half the step, because the error shows on both parts.
  • Gap or blunt corner: adjust the fence. See Troubleshooting below.

Expect two or three test cuts. Move in tiny steps: small adjustments make a big difference.

07

Save a setup block

Turn your perfect test piece into a one-minute setup for next time.

  1. Keep one perfect test piece and write the bit size and stock thickness on it.
  2. Next time, raise the bit until it fits the profile on the block exactly.
  3. Bring the fence up to the block, lock it, and you're ready to cut.
?

Troubleshooting

Find what you see, then make one adjustment at a time.

ProblemOne face sticks out past the other
CauseBit height is off
FixMove the bit by half the step. If the step grows on the next test, go the other way.
ProblemBlunt, flat corner
CauseBit doesn't protrude far enough
FixMove the fence back to expose a little more bit.
ProblemBoard got narrower / gap in the joint
CauseBit protrudes too far
FixMove the fence forward to cover a little of the bit.
ProblemJoint fits on one end, not the other
CauseBoard lifted or tipped during the cut
FixAdd featherboard pressure, keep part B vertical, use a tall fence.
ProblemBurn marks or rough surface
CauseFeed too slow, speed too high or dirty bit
FixFeed steadily, check the speed table, clean resin off the bit.
ProblemTear-out at the end of the cut
CauseUnsupported end grain
FixBack the cut with a square scrap of the same thickness.
+

Pro tips

Small habits that give cleaner joints and longer bit life.

Lighter passes in hardwoodStart with the fence slightly forward and reach the final position in 2–3 passes.
Remove waste firstChamfer the corner on a table saw to take load off the bit.
Dry-fit everythingThe interlock self-aligns, so you need less clamping pressure than with a plain miter.
Keep the bit cleanRemove pitch and resin regularly for cleaner cuts and a longer life.

Safety first. Unplug the router before changing bits or making adjustments. Use the bit only in a router table, never hand-held. Wear eye and hearing protection, keep your hands clear of the bit, use featherboards and push blocks, and follow your router's manual.

Working with different thicknesses?

Get all three GaugeX™ lock miter sizes and be ready for any project.

Shop GaugeX™ Lock Miter Bits

Questions about your setup? Reply to your order email and our team will help.

© GaugeX™ · Lock Miter Router Bit Setup Guide